In the iron ore sintering process, the fine size of mm in the sinter base mix is influencing on the sinter mineralogy and sinter properties. The amount of adhering fine particles to nuclei is strongly influenced by moisture available for granulation. ... JSW Steel has setup Asia's largest beneficiation plant with a designed capacity of ...
Lump iron ore, fluxed/superfluxed sinter and acid/basic pellets are the major iron bearing materials. Because of high SiO 2 and Al 2 O 3 content in iron bearing materials, limestone and dolomite as fluxes are added in sintering process to promote the formation of low melting slag which helps in achieving the desired sinter properties.
LD slag contains high amount of CaO, iron, and MgO, thus recycling it through sintering process helps in the saving of flux and iron ore. The recycled wastes have some effect on sinter quality, strength and productivity. JSW Steel Limited is a Mtpa integrated steel plant and produces 2000 to 2500 tons of LD slag per day.
Abstract. Iron ore granulation is an indispensable process in the production of sinter that can influence and regulate the yield, efficiency and quality. Although a great deal of research has been done on the granulation process over the past decades, we still need to think about the current and future development of this process, as sinter is ...
This process allows the direct utilization of fine iron ores and coal instead of sinter and coke. The fluidized bed reactor system is fed with iron ore fines of a particle size smaller than 8 × 10 −3 m (Ahn et al., 2010) and additives such as limestone or dolomite. To heat up the raw iron ores in the last fluidized bed reactor (fluidized bed ...
Sintering is the most economic and widely used agglomeration process to prepare iron ore fines for blast furnace use. In this chapter, the sintering process is first described and the key steps of the sintering process, namely, granulation and thermal densification, are identified. Discussion is then focused on the effect of the chemical ...
HMDS Slag contains high amount of CaO, iron, and MgO, thus recycling it through sintering process helps in the saving of flux and iron ore. The recycled wastes have some effect on sinter quality, strength and productivity. JSW Steel Limited is a Mtpa integrated steel plant and produces 1400 to 1500 tons of HMDS Slag per day.
The coke breeze consumption in the JSW Steel Limited sinter plant was high compared to many other sinter plants in the world, and as there was a local shortage, optimisation in the sinter plants was necessary. FeO is an indicator of the thermal state of the sintering process and is employed as a quality control tool at many plants.
Abstract. In iron making process, sintering of iron ore fines is an integral step to utilize not only the ore fines but also to introduce a part of flux (limestone and dolomite) along with the sinter in blast furnace burden. In this way, the productivity of the furnace considerably improves. In this paper, some fundamental aspects such as the ...
Abstract Coke breeze is the most common fuel used in sintering, and its usage depends on the alumina content and fineness of the sinter mix. The coke breeze consumption in the JSW Steel Limited sinter plant was high compared to many other sinter plants in the world, and as there was a local shortage, optimisation in the sinter plants was necessary. FeO is an indicator of the thermal state of ...
Sinter is the primary feed material for making iron in a blast furnace. During the iron ore sintering process in iron and steel manufacturing, sinter is created by mixing iron ore concentrate with several additives such as limestone and silica to control the chemistry and then igniting it at 1200°C in a continuous beltfed furnace. The production of highquality sinter is crucial for assuring ...
Intensification of the iron ore sintering process was approached by injecting hydrogenrich gas into the sinter bed. The location of the injection was critical to the pyrolysis of the solid fuel, and the SOx and NOx emissions. After installing the injection system in the most appropriate zone, the process intensified, and the emissions were ...
The total reaction involved in the process of sintering is the sum of a number of reactions which involve reactions in heating zone, reactions in sintering zone and reactions in cooling zone. These reactions are illustrated schematically for typical sintering of a limefluxed haematite ore in Fig. 11. Fig. : Development of Minerals during ...
Optimization of FeO in iron ore sinter at JSW steel limited. Ironmak Steelmak (2013) Sun et al. Effect of FeO content in ore on the properties of sinter; ... Mathematical modeling of natural gas injection in iron ore sintering process and corresponding environmental assessment of CO 2 mitigation. Journal of Cleaner Production, Volume 332 ...
A Review of Calcium Ferrite in Sintering of Iron Ore and The Effect of Gangue Composition on Its Formation February 2023 Academic Journal of Science and Technology 5(1):2531
The mill scale contains high amounts of Fe and low amounts of silica and alumina. Thus, recycling it through the sintering process helps in the saving of raw materials like iron ore and limestone. This paper presents preliminary findings of a study that investigates the potential for recycling steel mill scale in the sintering process.
Abstract and Figures. Sinter plants process a mixture of iron ore fines, recycled ironmaking products, slagforming agents and solid fuel (coke) with the finality of obtaining a product with the ...
JSW Steel Limited, Toranagallu 583119, Bellary, Karnataka, India. Search for more papers by this author. Mahapatra, ... The selective granulation process is a new sintering process for high alumina iron ore fines, and can eliminate the adverse effects of 'hard to sinter' or 'unsuitable for ironmaking' ores. ...
Sintering, which is also called 'frittage,' is the process of forming a solid mass of material through heat and pressure without melting to the point of liquefaction. This process involves the atoms in materials diffusing across the particle boundaries and fusing together into one piece. Sintering occurs naturally in mineral deposits, and ...
The target basicity of iron ore sinter is set by blast furnace slag composition requirements, and therefore varies with the proportion of acid burden such as lump iron ore and pellets. Increasing the lump proportion of the burden will increase the target sinter basicity. The mineralogy of sinter produced with a range of basicity between and was analysed using optical point counting ...
Raw materials for iron ore sintering comprise iron ore nes, uxes, and several other types of raw materials. Based upon the dierent characteristics of iron ore nes, a raw material mix optimization model as shown in Fig. 2 is used for blending raw materials in respective (wt.%) for making feed for the sintering process. The raw material mix ...
These results indicate the suitability of recycling RM in the Egyptian iron ore sintering process with an amount not higher than 3 wt. % of the total sinter mixture charge. ... Sinter plant at JSW ...
© DZCrusher - كل الحقوق محفوظة
